Tadiran Telecom FlexSet 280S User Manual Download Page 212 | Manualshive

Page: 212 / 253

background image

Attendant Features

204

FlexSet 120S/280S User Guide

Trunk Setup Features

♦

[LAR]

Look Ahead Routing

is used to view the status of trunks/Dial Services that have been automatically

blocked from use for outgoing calls. The Coral system automatically blocks a trunk/Dial Service in
case of a failure to establish an outgoing connection via that trunk/Dial Service. The LAR Block feature
enables an attendant to manually block/unblock the failed trunk/Dial Service.

When

ASSIGN

appears in the display the trunk/Dial Service line is blocked.

DEASSIGN

means the

trunk/Dial Service line is in use by the system.
After unblocking a trunk/Dial Service, make an external call on the specific trunk/Dial Service. If the
call goes through, the trunk/Dial Service is unblocked. If the trunk/Dial Service is still blocked, call the
technician and re-activate LAR Block.
If LAR Block activation failed due to insufficient resources (the system ran out of LAR Service
Timers), the message

NO RESOURCE

appears upon dialing activation code.

NOTE:

If the trunk/Dial Service was manually blocked, it can only be unblocked manually. Automatic
unblock will not work in this case.

♦

[Block]

Central Office (CO) Block

is used to view which of the trunks have been blocked at the central office.

When

ASSIGN

appears in the display the trunk line is blocked for both outgoing and incoming calls.

DEASSIGN

means the trunk line is in use by the system.

♦

[BsyOut]

Busy Out

is used to block any trunk for both incoming and outgoing calls. (This feature may be used to

block faulty trunks until the CO service is restored.) When

ASSIGN

appears in the display the trunk line

is blocked.

DEASSIGN

means the trunk line is in use by the system.

[DIL-x]

Direct In Line (DIL)

is used to program incoming CO lines to ring directly at a specific destination

depending on the required service mode (Day, Night 1, Night 2), without intervention. Possible
destinations are

operator, station, hunt group, boss group, UNA/central bell, public speed call, voice

mail, modem, group call, pre-recorded DVMS message, wait queue and network number

.

[DIL-D]

DIL at Day service period.

[DIL-N1]

DIL at Night 1 service period.

[DIL-N2]

DIL at Night 2 service period.

♦

[DropND]

Drop No Dial

is used to program an outgoing trunk to be dropped when a caller does not dial the first

digit within a system-wide time limit. The trunk is then made available to other users.

«
...
210
211
212
213
214
...
»

Summary of Contents for FlexSet 280S






























































































































































































































































Reviews:

No comments

Related manuals for FlexSet 280S

Brand: NEFFOS Pages: 32

Brand: Pantech Pages: 2

Brand: N-Com Pages: 32

Brand: NEC Pages: 7

Brand: NEC Pages: 68

Brand: NEC Pages: 44

Brand: UMX Pages: 56

Brand: Samsung Pages: 283

Brand: Krüger & Matz Pages: 20

Brand: ZTE-G Pages: 51

Brand: IPitomy Pages: 117

INNOVAPHONE 200

Brand: TIPTEL Pages: 32

Brand: Sagem Pages: 97

BLACKVIEW BV6000

Brand: Iget Pages: 52

Brand: SoftBank Pages: 19

Brand: Hisense Communications Pages: 24

Brand: Zte Pages: 198

Brand: Hisense Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands