manualshive.com logo in svg

Suzuki SMD12, Operator'S Manual

The Suzuki SMD12 Operator's Manual is the essential companion for any Suzuki SMD12 owner. With easy-to-follow instructions and detailed diagrams, this manual guides users through every aspect of operating and maintaining their SMD12. Download it for free from our website now and unlock the full potential of your Suzuki SMD12.

Share
Download
background image

10-1

10. FILE OPERATIONS

Points, tracks, routes and settings can be read and written, using the USB port, SD 
card unit. Further, with a My Time Zero

™

* account, you can save settings data to the 

cloud. The card slot at the back of the SMD12/SMD16 is exclusively for use with chart 
cards.

* Only boundary line data can be imported. Boundary lines can be created with 
TIMEZERO Marine Software.

The table below outlines the media that can be used with your unit.

Note 1: 

For care and handling of microSD, see section 1.10.

Note 2: 

[Convert Old Data Format] cannot be used.

Handling USB flash memory

•  Format the USB flash memory to file system FAT32. The capacity of the media 

should be 32GB or less.

•  Do not use a secure USB flash memory or SD card.
•  Turn off the power before inserting or removing the media connected to the USB 

port, to prevent corruption of data.

10.1

File Format

You can select the file format to use to export data.

1. Open the home screen, then tap [Settings] - [Files].

2. Tap [Export File Format].

Action

MicroSD

USB port

SD Card Unit 

(SMD12/SMD16, 

option)

SD card 

converter 

adapter

Write data

Yes

Yes

Yes

Read data

Yes

Yes

Yes

Summary of Contents for SMD12



















































































































































































































































































































































Reviews:

No comments

Related manuals for SMD12

Eizo RADIFORCE RX220 User Manual preview
RADIFORCE RX220
Brand: Eizo Pages: 46
Ebird VLCD-5 Operation Manual preview
VLCD-5
Brand: Ebird Pages: 11
EBN Technology SPPC70-5B-C1G Service Manual preview
SPPC70-5B-C1G
Brand: EBN Technology Pages: 20
Samsung SyncMaster 933SN User Manual preview
SyncMaster 933SN
Brand: Samsung Pages: 59
Hama Baby-Control BC-400D Operating Instructions Manual preview
Baby-Control BC-400D
Brand: Hama Pages: 75
S&S Northern Merlin PM2+ User Manual preview
Merlin PM2+
Brand: S&S Northern Pages: 8
Barco MDSC-2326 MNAH User Manual preview
MDSC-2326 MNAH
Brand: Barco Pages: 78
A&A Tech EEM MOT 01 FL02.01 Operator And Maintenance Manual preview
EEM MOT 01 FL02.01
Brand: A&A Tech Pages: 16
Hanns.G HH241 User Manual preview
HH241
Brand: Hanns.G Pages: 23
Barco RHDM-2301 User Manual preview
RHDM-2301
Brand: Barco Pages: 174
Kidde KN-COU-B User Manual preview
KN-COU-B
Brand: Kidde Pages: 19
Barco HVD5521 User Manual preview
HVD5521
Brand: Barco Pages: 91
Eizo FLEXSCAN HD2441W - SETUP User Manual preview
FLEXSCAN HD2441W - SETUP
Brand: Eizo Pages: 52
AOC LM929 - 19" (Portuguese) Specification Sheet preview
LM929 - 19"
Brand: AOC Pages: 1
Velleman MONCOLHA5PN4 Manual preview
MONCOLHA5PN4
Brand: Velleman Pages: 8
ViewSonic VA2038w-LED VS13400 User Manual preview
VA2038w-LED VS13400
Brand: ViewSonic Pages: 25
ViewSonic VG2753 User Manual preview
VG2753
Brand: ViewSonic Pages: 25
Daktronics CH-1421V Installation & Maintenance Manual preview
CH-1421V
Brand: Daktronics Pages: 24

Brands by name

Popular brands

Load more brands