manualshive.com logo in svg

Suzuki SMD12, Operator'S Manual

The Suzuki SMD12 Operator's Manual is the essential companion for any Suzuki SMD12 owner. With easy-to-follow instructions and detailed diagrams, this manual guides users through every aspect of operating and maintaining their SMD12. Download it for free from our website now and unlock the full potential of your Suzuki SMD12.

Share
Download
background image

7.  RADAR

7-24

is only able to sense the motion directly along the radial, either towards or away from 
the radar, because the transverse component has no effect on the phase of the return-
ing electromagnetic wave.

The figure below shows an actual radar image with the target analyzer activated.

Operating mode and range

Single range: 0.063 to 72 NM, Target Analyzer ON, single range: 0.063 to 24 NM
Dual range: 0.063 to 12 NM, Target Analyzer ON, dual range: 0.063 to 12 NM

Radar

Total 
velocity

Transverse 
component

Radial component

Radial

Radar measures the
radial component of 
velocity only

Target Analyzer: OFF

Target Analyzer: Target Mode

Target Analyzer: Rain Mode

Approaching
target (red)

Approaching
target (red)

Approaching
targets (red)

Approaching
targets (red)

Rain (blue)

Rain (blue)

Target Mode

Rain Mode

Approaching targets: 

RED

Other targets: 

GREEN

Approaching targets: 

RED

Rain: 

BLUE

Other targets: 

GREEN

Summary of Contents for SMD12



















































































































































































































































































































































Reviews:

No comments

Related manuals for SMD12

d.s.f. IG 47 A03 Operating Instruction preview
IG 47 A03
Brand: d.s.f. Pages: 8
Mackie HR824 Service Manual preview
HR824
Brand: Mackie Pages: 39
uebe visomat comfort 20/40 Instructions For Use Manual preview
visomat comfort 20/40
Brand: uebe Pages: 33
uAvionix AV-30-C Instructions For Continued Airworthiness preview
AV-30-C
Brand: uAvionix Pages: 22
Waveshare 13.3 inch HDMI LCD (H) User Manual preview
13.3 inch HDMI LCD (H)
Brand: Waveshare Pages: 12
Wells-Gardner D9100 Series Service Manual preview
D9100 Series
Brand: Wells-Gardner Pages: 25
Fametech PPD-1210 User Manual preview
PPD-1210
Brand: Fametech Pages: 23
Melissa 630-013 User Manual preview
630-013
Brand: Melissa Pages: 51
A&A Tech EEM MOT 01 Operator And Maintenance Manual preview
EEM MOT 01
Brand: A&A Tech Pages: 16
Summer BABYTOUCH 29763Z Instruction Manual preview
BABYTOUCH 29763Z
Brand: Summer Pages: 12
Lollipop Smart Baby Camera User Manual preview
Smart Baby Camera
Brand: Lollipop Pages: 5
VESTEL IF86TI630B/6 User Manual preview
IF86TI630B/6
Brand: VESTEL Pages: 136
Sceptre D73P User Manual preview
D73P
Brand: Sceptre Pages: 20
B&G h1000 CND Manual preview
h1000 CND
Brand: B&G Pages: 61
Sentinel MO52 Installation & Operation Manual preview
MO52
Brand: Sentinel Pages: 11
Oceanic Systems NMEA2000 5115 User Manual preview
NMEA2000 5115
Brand: Oceanic Systems Pages: 8
FDS FD141CV-C-6 Installation And Operation Manual preview
FD141CV-C-6
Brand: FDS Pages: 34
Prowise ProLine+ Faq preview
ProLine+
Brand: Prowise Pages: 7

Brands by name

Popular brands

Load more brands