manualshive.com logo in svg

Suzuki SMD12, Operator'S Manual

The Suzuki SMD12 Operator's Manual is the essential companion for any Suzuki SMD12 owner. With easy-to-follow instructions and detailed diagrams, this manual guides users through every aspect of operating and maintaining their SMD12. Download it for free from our website now and unlock the full potential of your Suzuki SMD12.

Share
Download
background image

1.  SYSTEM INTRODUCTION

1-2

1.1

Controls

The SMD12 and SMD16 are operated by a power switch on the front panel and a mi-
croSD card slot, which is used for chart data, is on the rear panel. The power switch 
is also used to adjust brilliance.

You can operate the SMD12/16 by touch controls, on the screen.

Multi-Function Display (shown in optional hanger)

About the soft cover

The soft cover protects the LCD when the display unit is 
not in use. To remove the cover, grasp the cover at the 
locations circled in the right figure and pull forward.

Touchscreen operations

The tables which follow outline the touchscreen opera-
tions.

No.

Item

Function

1

(Power switch)

•  Turns the power on.
•  Adjust the brilliance and hue of the display.
•  Turns the power off (device or network).
•  Locks, unlocks the touch screen.

2

Card slot

•  This slot is exclusively for use with chart cards.

1

2

SMD16

SMD12

1

2

Summary of Contents for SMD12



















































































































































































































































































































































Reviews:

No comments

Related manuals for SMD12

NEC MD461OR Installation & Maintenance Manual preview
MD461OR
Brand: NEC Pages: 14
Magnavox 51MP392H - 51" Widescreen Hd Ready Tv Setup Manual preview
51MP392H - 51" Widescreen Hd Ready Tv
Brand: Magnavox Pages: 7
CALMPER BM600 User Manual preview
BM600
Brand: CALMPER Pages: 18
Barco Encore Controller SC Brochure preview
Encore Controller SC
Brand: Barco Pages: 6
Mitsubishi DPLUS 74SB -BKB Service Manual preview
DPLUS 74SB -BKB
Brand: Mitsubishi Pages: 176
CueScript CSTD Manual preview
CSTD
Brand: CueScript Pages: 5
Wachendorff DA9602 Operating Manual preview
DA9602
Brand: Wachendorff Pages: 15
YURAKU MJ7C User Manual preview
MJ7C
Brand: YURAKU Pages: 34
Viotek GNV34DB2 User Manual preview
GNV34DB2
Brand: Viotek Pages: 16
Electro-mech LX2056 Owner'S Manual preview
LX2056
Brand: Electro-mech Pages: 29
Lorex Baby BB7011 User Manual preview
Baby BB7011
Brand: Lorex Pages: 24
iHealth BP5S Instructions For Use Manual preview
BP5S
Brand: iHealth Pages: 210
A&D UA-853 Instruction Manual preview
UA-853
Brand: A&D Pages: 100
Acura Embedded ACUBRITE 19-Nav User Manual preview
ACUBRITE 19-Nav
Brand: Acura Embedded Pages: 40
BAFANG DP C07.CAN User Manual preview
DP C07.CAN
Brand: BAFANG Pages: 14
Volanti VD-6500-0B09-1100 Quick Start preview
VD-6500-0B09-1100
Brand: Volanti Pages: 2
Chimei 23 58cm User Manual preview
23 58cm
Brand: Chimei Pages: 10
Waveshare 7inch HDMI LCD User Manual preview
7inch HDMI LCD
Brand: Waveshare Pages: 7

Brands by name

Popular brands

Load more brands