Supero AS-1010S-T User Manual Download

Page: 48 / 100

5-14

AS1010S-T User's Manual

Power Button

The Power Button connection is

located on pins 1 and 2 of JF1. Mo-

mentarily contacting both pins will

power on/off the system. This button

can also be conﬁ gured to function

as a suspend button (see the Power

Button Mode setting in BIOS). To turn

off the power when set to suspend

mode, depress the button for at least

4 seconds. Refer to the table on the

right for pin deﬁ nitions.

USB0/1 (Universal Serial
Bus Ports)

Two Universal Serial Bus ports

(USB2.0) are located beside the

keyboard/mouse ports on the I/O

backpanel. See the table on the right

for pin deﬁ nitions.

Power Button

Pin Deﬁ nitions (JF1)

Pin# Deﬁ nition

PW_ON

Ground

Universal Serial Bus Ports

Pin Deﬁ nitions (USB0/1)

USB0
Pin # Deﬁ nition

USB1
Pin # Deﬁ nition

+5V

PO-

PO+

Ground

Reset Button

The Reset Button connection is lo-

cated on pins 3 and 4 of JF1. Attach

it to the hardware reset switch on the

computer case. Refer to the table on

the right for pin deﬁ nitions.

Reset Button

Pin Deﬁ nitions (JF1)

Pin# Deﬁ nition

Reset

Ground

Serial ATA Activity LEDs

Connect an LED to the JS9 header to

provide indication of Serial ATA drive

activity. See the table on the right for

pin deﬁ nitions.

Serial ATA Activity LEDs

Pin Deﬁ nitions (JS9)

Pin # Deﬁ nition

SATA0 LED

SATA1 LED

SATA2 LED

SATA3 LED

Ground

Key

Note:

NC indicates no connection.

Summary of Contents for AS-1010S-T





































































































Search results

Summary of Contents for AS-1010S-T

Reviews:

Related manuals for AS-1010S-T

Brands by name

Popular brands

Supero AS-1010S-T, User Manual

Search results

Summary of Contents for AS-1010S-T

Reviews:

Related manuals for AS-1010S-T

Brands by name

Popular brands