Supero AS-1010S-T User Manual Download

Page: 15 / 100

Chapter 1: Introduction

1-5

1-3 Server

Chassis

Features

The 1010S-T is a mini 1U rackmount server platform conﬁ guration. The following

is a general outline of the main features of the SC811FT-260 chassis.

System Power

When conﬁ gured as a 1010S-T, the SC811FT-260 chassis includes a single 260W

power supply.

Control Panel

The SC811FT-260's control panel provides important system monitoring and control

information. LEDs indicate power on, network activity, hard disk drive activity and

overheat/fan fail conditions. The control panel also includes a main power button

and a system reset button.

Rear I/O Panel

The SC811FT-260 is a 1U rackmount chassis. Its I/O panel provides one expan-

sion card slot, one COM port, two USB ports, PS/2 mouse and keyboard ports, a

graphics port and two Gb Ethernet ports. (See Chapter 6 for details.)

Cooling System

The SC811FT-260 chassis has an innovative cooling design that features two 4-

cm heavy-duty, counter-rotating fans. A fan speed control setting in BIOS allows

fan speed to be determined by system temperature [the recommended setting is

3-pin (Server)].

Summary of Contents for AS-1010S-T





































































































Search results

Summary of Contents for AS-1010S-T

Reviews:

Related manuals for AS-1010S-T

Brands by name

Popular brands

Supero AS-1010S-T, User Manual

Search results

Summary of Contents for AS-1010S-T

Reviews:

Related manuals for AS-1010S-T

Brands by name

Popular brands