manualshive.com logo in svg

Supero AS-1010S-T, User Manual

Share
Download
Supero AS-1010S-T User Manual Download Page 43

Chapter 5: Advanced Motherboard Setup

5-9

5-7 Adding 

PCI 

Cards

1.

 

PCI slots:

 

 

 

 

 

 

 

 

The H8SSL-i has three PCI expansion slots.  One of these slots (the 133 MHz PCI-

X slot #6) may be populated with the use of the CSE-RR1U-X riser card, which is 

included with the system.  You may install either a 133 or a 100 MHz PCI-X card 

into the riser card. 

2.

 

PCI card installation:

   

 

 

 

 

 

Before installing a PCI add-on card, make sure it is supported by the riser card (see 

step 1, above).  Begin by pulling the locking tab downward to unlock the bracket 

that covers the slot, then remove the bracket.  Insert the PCI card into the riser 

card, pushing down with your thumbs evenly on both sides of the card.  When the 

card is correctly installed, fi nish by pushing the locking tab upward to secure the 

card in the system. 

Note:

 the PCI slot shield helps promote proper airlow in the chassis and shield the 

inside of the system from EMI (electromagnetic interference).  For these reasons, 

make sure there is a shield covering the slot if unused.

Summary of Contents for AS-1010S-T





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands