Supero AS-1010S-T User Manual Download

Page: 7 / 100

Chapter 5: Advanced Motherboard Setup

5-1 Handling

the

Motherboard

...............................................................................

5-1

5-2 Mounting the Motherboard into a Chassis ...................................................... 5-2

5-3 Processor and Heatsink Installation ................................................................ 5-2

5-4 Connecting Cables .......................................................................................... 5-5

Connecting Data Cables ........................................................................... 5-5

Connecting Power Cables ......................................................................... 5-5

Connecting the Control Panel ................................................................... 5-6

5-5 I/O Ports ......................................................................................................... 5-7

5-6 Installing

Memory

............................................................................................. 5-7

5-7 Adding PCI Cards ............................................................................................ 5-9

5-8 Motherboard

Details

.....................................................................................

5-10

H8SSL-i Layout ....................................................................................... 5-10

H8SSL-i Quick Reference ....................................................................... 5-11

5-9 Connector

Deﬁ

nitions

....................................................................................

5-11

Primary ATX Power Connector ............................................................. 5-12

Secondary Power Connector .................................................................. 5-12

NMI Button ............................................................................................ 5-12

Power LED .............................................................................................. 5-12

HDD LED .............................................................................................. 5-13

NIC1/NIC2 LED ...................................................................................... 5-13

Overheat/Fan Fail LED .......................................................................... 5-13

Power Fail LED ...................................................................................... 5-13

Reset Button ......................................................................................... 5-14

Power Button ......................................................................................... 5-14

Universal Serial Bus (USB0/1) ................................................................ 5-14

Serial ATA Activity LEDs ......................................................................... 5-14

USB2/3 Headers .................................................................................... 5-15

Serial Ports .............................................................................................. 5-15

Fan Headers ............................................................................................ 5-15

Overheat LED .......................................................................................... 5-15

Power LED/Speaker ............................................................................... 5-16

ATX PS/2 Keyboard and Mouse Ports .................................................... 5-16

Wake-On-Ring .......................................................................................... 5-16

Wake-On-LAN ........................................................................................ 5-16

LAN 1/2 (Ethernet Ports) ....................................................................... 5-17

Chassis Intrusion .................................................................................... 5-17

IPMI Header ........................................................................................... 5-17

Power Supply Fail Alarm Header ........................................................... 5-17

vii

Table of Contents

Summary of Contents for AS-1010S-T





































































































Search results

Summary of Contents for AS-1010S-T

Reviews:

Related manuals for AS-1010S-T

Brands by name

Popular brands

Supero AS-1010S-T, User Manual

Search results

Summary of Contents for AS-1010S-T

Reviews:

Related manuals for AS-1010S-T

Brands by name

Popular brands