Supero AS-1010S-T User Manual Download

Page: 53 / 100

Chapter 5: Advanced Motherboard Setup

5-19

Onboard Speaker Enable/
Disable

The JD1 header allows you to use

either an external speaker or the

internal (onboard) speaker. To use

the internal (onboard) speaker, close

pins 6 and 7 with a jumper. To use an

external speaker, connect the speaker

wires to pins 4 through 7 of JD1. See

the table on the right for settings and

the table associated with the Power

LED/Speaker connection (previous

section) for pin deﬁ nitions.

Onboard Speaker Enable/Disable

Pin Deﬁ nitions (JD1)

Pins Deﬁ nition

6-7

Jump for onboard speaker

4-7

Attach external speaker wires

VGA Enable/Disable

JPG1 allows you to enable or disable

the VGA port. The default position is

on pins 1 and 2 to enable VGA. See

the table on the right for jumper set-

tings.

VGA Enable/Disable

Jumper Settings (JPG1)

Jumper Setting Deﬁ nition

Pins 1-2

Enabled

Pins 2-3

Disabled

LAN Enable/Disable

Change the setting of jumper JPL to

enable or disable the LAN1 and LAN2

Gb Ethernet ports. See the table on

the right for jumper settings. The

default setting is enabled.

JLAN1/2 Enable/Disable

Jumper Settings (JPL)

Jumper Setting Deﬁ nition

Pins 1-2

Enabled

Pins 2-3

Disabled

PCI-X Slot Speed

Jumpers JPXA1 can be used to change

the speed of PCI-X slot #6. See the

table on the right for jumper settings.

PCI-X Slot Speed Jumper Settings

(JPXA1)

Jumper Setting Deﬁ nition

Open

Auto

Pins 1-2

PCI-X 66 MHz

Pins 2-3

PCI 66 MHz

Summary of Contents for AS-1010S-T





































































































Search results

Summary of Contents for AS-1010S-T

Reviews:

Related manuals for AS-1010S-T

Brands by name

Popular brands

Supero AS-1010S-T, User Manual

Search results

Summary of Contents for AS-1010S-T

Reviews:

Related manuals for AS-1010S-T

Brands by name

Popular brands