Supero AS-1010S-T User Manual Download Page 40

Page: 40 / 100

5-6

AS1010S-T User's Manual

Figure 5-2. Front Control Panel Header Pins (JF1)

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure

5-2 for the pin locations of the various front control panel buttons and LED indica-

tors and refer to section 5-9 for details. Note that even and odd numbered pins

are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their

connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect

the other end of the cable to the Control Panel printed circuit board, located just

behind the system status LEDs in the chassis.

See the Connector Deﬁ nitions section in this chapter for details and pin descrip-

tions of JF1.

NMI

x (key)

Vcc

Reset Button

Power Button

Ground

x (key)

Power LED

HDD LED

NIC1

NIC2

OH/Fan Fail LED

Power Fail LED

Ground

2 1

20 19

Summary of Contents for AS-1010S-T





































































































Search results

Summary of Contents for AS-1010S-T

Reviews:

Brands by name

Popular brands

Supero AS-1010S-T, User Manual

Search results

Summary of Contents for AS-1010S-T

Reviews:

Brands by name

Popular brands