Supero AS-1010S-T User Manual Download Page 65

Page: 65 / 100

Chapter 6: Advanced Chassis Setup

6-3

6-3 System

Fans

Two 4-cm fans provide the cooling for the 1010S-T. Each fan unit is actually made

up of two fans joined back-to-back, which rotate in opposite directions. This counter-

rotating action generates exceptional airﬂ ow and works to dampen vibration levels.

These fans can adjust their speed according to the heat level sensed in the system,

which results in more efﬁ cient and quieter fan operation. Fan speed is controlled by a

setting in BIOS (see Chapter 7). Each fan in a set has its own separate tachometer.

An air shroud is also included with the system to optimize airﬂ ow.

Note:

It is very important that the chassis top cover is properly installed for the

airﬂ ow to circulate properly through the chassis and cool the components.

System Fan Failure

If a fan fails, the remaining fans will ramp up to full speed and the overheat/fan

fail LED on the control panel will blink on and off. Replace any failed fan at your

earliest convenience with the same type and model (the system can continue to

run with a failed fan). Remove the top chassis cover (refer to page 6-7) while the

system is still running to determine which fan unit has failed, then power down

the system to replace it. Removing the power cord(s) is also recommended as a

safety precaution.

Replacing System Cooling Fans

Removing a fan

With the system powered down, ﬁ rst unplug the failed fan cable from the mother-

board. Grasp the failed fan unit and lift it out of the chassis.

Installing a new fan

Replace the failed fan with an identical 4-cm, 12 volt fan (p/n FAN-0087). At the

bottom of each fan unit there are four small rubber pieces that help position the

fan into place in the chassis. Remove these from the failed fan and attach them

to the new fan (new fans do not include this piece). Then place the new fan in the

housing with the fan wiring toward the motherboard. Reconnect the fan wiring to

the same fan header you removed it from. Power up the system and check that

the fan is working properly and that the LED on the control panel has turned off.

Finish by replacing the chassis cover.

Summary of Contents for AS-1010S-T





































































































Search results

Summary of Contents for AS-1010S-T

Reviews:

Brands by name

Popular brands

Supero AS-1010S-T, User Manual

Search results

Summary of Contents for AS-1010S-T

Reviews:

Brands by name

Popular brands