Supermicro SUPERSERVER 6015V-MR User Manual Download Page 71

Page: 71 / 114

Chapter 7: BIOS

7-3

Main BIOS Setup Menu

Main Setup Features

System Time

To set the system date and time, key in the correct information in the appropriate

ﬁ elds. Then press the <Enter> key to save the data.

System Date

Using the arrow keys, highlight the month, day and year ﬁ elds, and enter the correct

data. Press the <Enter> key to save the data.

BIOS Date

This ﬁ eld displays the date when this version of BIOS was built.

Legacy Diskette A

This setting allows the user to set the type of ﬂ oppy disk drive installed as diskette A.

The options are Disabled, 360Kb 5.25 in, 1.2MB 5.25 in, 720Kb 3.5 in,

1.44/1.25MB

3.5 in and 2.88MB 3.5 in.

Summary of Contents for SUPERSERVER 6015V-MR



















































































































Search results

Summary of Contents for SUPERSERVER 6015V-MR

Reviews:

Related manuals for SUPERSERVER 6015V-MR

Brands by name

Popular brands

Supermicro SUPERSERVER 6015V-MR, User Manual

Search results

Summary of Contents for SUPERSERVER 6015V-MR

Reviews:

Related manuals for SUPERSERVER 6015V-MR

Brands by name

Popular brands