Supermicro SUPERSERVER 6015V-MR User Manual Download Page 84

Page: 84 / 114

7-16

UPER

ERVER 6015V-MR/6015V-MRLP User's Manual

DMI Event Logging

Access the submenu to make changes to the following settings.

Event Log Validity

This is a display to inform you of the event log validity. It is not a setting.

Event Log Capacity

This is a display to inform you of the event log capacity. It is not a setting.

View DMI Event Log

Highlight this item and press <Enter> to view the contents of the event log.

Event Logging

This setting allows you to

Enable

or Disable event logging.

ECC Event Logging

This setting allows you to

Enable

or Disable ECC event logging.

Mark DMI Events as Read

Highlight this item and press <Enter> to mark the DMI events as read.

Clear All DMI Event Logs

Select Yes and press <Enter> to clear all DMI event logs. The options are Yes

and

Summary of Contents for SUPERSERVER 6015V-MR



















































































































Search results

Summary of Contents for SUPERSERVER 6015V-MR

Reviews:

Related manuals for SUPERSERVER 6015V-MR

Brands by name

Popular brands

Supermicro SUPERSERVER 6015V-MR, User Manual

Search results

Summary of Contents for SUPERSERVER 6015V-MR

Reviews:

Related manuals for SUPERSERVER 6015V-MR

Brands by name

Popular brands