Super PDSMi Page 56 User Manual Download

Page: 56 / 100

4-8

PDSMi User's Manual

Power Button Behavior

If set to Instant-Off, the system will power off immediately as soon as the user

hits the power button. If set to 4-sec., the system will power off when the user

presses the power button for 4 seconds or longer. The options are

instant-off

and 4-sec override.

Resume On Modem Ring

Select On to "wake your system up" when an incoming call is received by your

modem. The options are

and Off.

Power Loss Control

This setting allows you to choose how the system will react when power returns

after an unexpected loss of power. The options are

Last State,

Stay off, and

Power On.

Watch Dog

If enabled, this option will automatically reset the system if the system is not

active for more than 5 minutes. The options are Enabled and

Disabled

Summary Screen

This setting allows you to

Enable

or Disable the summary screen which displays

the system conﬁ guration during bootup.

Memory Cache

Cache Memory

Set to enabled to set the state of Cache Memory. The options are

Enabled

and Disabled.

Cache System BIOS Area

This setting allows you to designate a reserve area in the system memory to

be used as a System BIOS buffer to allow the BIOS write (cache) its data into

this reserved memory area. Select "

Write Protect

" to enable this function, and

this area will be reserved for the BIOS ROM access only. Select "Uncached" to

disable this function and make this area available for other devices.

Summary of Contents for PDSMi





































































































Search results

Summary of Contents for PDSMi

Reviews:

Related manuals for PDSMi

Brands by name

Popular brands

Super PDSMi, User Manual

Search results

Summary of Contents for PDSMi

Reviews:

Related manuals for PDSMi

Brands by name

Popular brands