Super PDSMi Page 13 User Manual Download

Page: 13 / 100

Chapter 1: Introduction

1-7

PC Health Monitoring

• Onboard voltage monitors for CPU cores, Chipset Voltage, Memory Voltage,

+3.3V,

5V, +5V Standby, +12V, and

−

12V

• CPU 4-phase-switching voltage regulator

• Status monitor for fan speed & System OH/Fan Fail LED/Control

• Pulse Width Modulation Fan Control & Low noise fan speed control

• Environmental temperature monitoring via BIOS, PWR-Up from AC PWR loss

• SuperDoctor

III,

NMI

• System Resource alert via SuperDoctor III

ACPI Features

• Slow blinking LED for suspend state indicator

• BIOS support for USB keyboard

• Main switch override mechanism

• Internal/external

modem

ring-on

Onboard I/O

• 1

ATA/100

EIDE

Channel

• Intel ICH7R SATA Controller, 4 connectors for 4 devices with support of RAID

functions 0, 1, 5 and 10

• 1 ﬂ oppy port interface (up to 2.88 MB)

• 1 Fast UART 16550 compatible serial port and 1 header

• Two Intel single-port 82573 PCI-E Gigabit Ethernet Controller

• PS/2 mouse and PS/2 keyboard ports

• Up to 6 USB (Universal Serial Bus) 2.0 ports for a speed

• VGA Connector

• Low Proﬁ le IPMI 2.0

• Super I/O (Winbond 83627 HF) with hardware monitoring (W83792DL)

• ATI Rage XL 8 MB

Temperature

• Monitoring

CPU,

chassis

environment

• CPU

Thermal

Trip

support

• Thermal Monitor 2 (TM2) (available if supported by the CPU)

Other

• Wake-on-LAN

(WOL)

• Wake-on-Ring

(WOR)

• Onboard Standby PWR warning LED Indicator ("LE 1")

CD Utilities

• Drivers and software for Intel E7230 chipset utilities

Dimensions

• 9.6" (W) x 12" (L) (243.84 mmx 304.8 mm)

Summary of Contents for PDSMi





































































































Search results

Summary of Contents for PDSMi

Reviews:

Related manuals for PDSMi

Brands by name

Popular brands

Super PDSMi, User Manual

Search results

Summary of Contents for PDSMi

Reviews:

Related manuals for PDSMi

Brands by name

Popular brands