Super PDSMi Page 18 User Manual Download

Page: 18 / 100

1-12

PDSMi

User’s Manual

The

PDSMi accommodates 12V ATX power supplies. Although most

power supplies generally meet the speciﬁ cations required by the CPU, some are

inadequate. A 2 amps of current supply on a 5V Standby rail is strongly recom-

mended.

The PDSMi accommodates ATX power supplies. It is strongly recommended that

you use a high quality power supply that meets ATX power supply Speciﬁ cation 2.02

or above. You should use one that will supply at least 350W of power. Also your

power supply must supply 1.5A for the Ethernet ports. It must also be SSI compliant

(info at http://www.ssiforum.org/). Additionally, in areas where noisy power transmis-

sion is present, you may choose to install a line ﬁ lter to shield the computer from

noise. It is recommended that you also install a power surge protector to help avoid

problems caused by power surges.

Summary of Contents for PDSMi





































































































Search results

Summary of Contents for PDSMi

Reviews:

Related manuals for PDSMi

Brands by name

Popular brands

Super PDSMi, User Manual

Search results

Summary of Contents for PDSMi

Reviews:

Related manuals for PDSMi

Brands by name

Popular brands