Super PDSMi User Manual Download Page 8

Page: 8 / 100

1-2

PDSMi

User’s Manual

Contacting Supermicro

Headquarters

Address:

SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel:

+1 (408) 503-8000

Fax:

+1 (408) 503-8008

Email:

[email protected] (General Information)

[email protected]

(Technical

Support)

Web Site:

www.supermicro.com

Europe

Address:

SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel:

+31 (0) 73-6400390

Fax:

+31 (0) 73-6416525

Email:

[email protected] (General Information)

[email protected]

(Technical

Support)

[email protected]

(Customer

Support)

Asia-Paciﬁ c

Address:

SuperMicro,

Taiwan

4F, No. 232-1 Liancheng Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.

Tel:

+886-(2)

8226-3990

Fax:

+886-(2) 8226-3991

Web Site:

www.supermicro.com.tw

Technical

Support:

Email:

[email protected]

Tel:

886-2-8228-1366, ext.132 or 139

Summary of Contents for PDSMi





































































































Search results

Summary of Contents for PDSMi

Reviews:

Super PDSMi, User Manual, Page: 8 / 100

Search results

Summary of Contents for PDSMi

Reviews: