SunSynk ECCO SUN-3.6K-SG05LP1-EU User Manual Download

Page: 59 / 71

ECCO SG04LP1 | User Manual

Aux Load off Battery % or

Voltage

Battery level when the Aux load switches off

Aux Load on Battery % or

Voltage

Battery level when the Aux load switches on.

Solar Power

Power limiter to the maximum power allowed to the Aux load.

Gen Input

Tick this box if using a Generator.

Aux Load Output

Tick this box if using an Aux or Smart Load.

For Micro inverter Input

Tick this box if intending to connect a supplementary inverter or micro

inverter (Max. 4kW).

Zero Export

Tick this box to stop exporting power produced by the Aux Load.

Gen Peak Shaving

Tick this box to use peak power shaving.

5.22. Advanced Settings for Peak Shaving

To configure Peak Power Shaving function, click on the AUX LOAD icon.

What this page displays:

Generator peak shaving is ON or OFF.

Peak Power Shaving value.

What you can do from this page:

Switch on the generator and/or grid peak
power saving and set the power shaving
value.

Peak Shaving:

This is a technique used to reduce electrical power consumption during periods of maximum

demand on the utility grid. This enables the user to save substantial amounts of money due to the expensive

peak power charges.

Summary of Contents for ECCO SUN-3.6K-SG05LP1-EU








































































Search results

Summary of Contents for ECCO SUN-3.6K-SG05LP1-EU

Reviews:

Related manuals for ECCO SUN-3.6K-SG05LP1-EU

Brands by name

Popular brands

SunSynk ECCO SUN-3.6K-SG05LP1-EU, User Manual

Search results

Summary of Contents for ECCO SUN-3.6K-SG05LP1-EU

Reviews:

Related manuals for ECCO SUN-3.6K-SG05LP1-EU

Brands by name

Popular brands