manualshive.com logo in svg

SunSynk ECCO SUN-3.6K-SG05LP1-EU, User Manual

Share
Download
SunSynk ECCO SUN-3.6K-SG05LP1-EU User Manual Download Page 69

ECCO SG04LP1 | User Manual

69

APPENDIX B

Inverters sold in Australia will be set to the Default Australian standards

APPENDIX C

The Sunsynk Single-Phase Hybrid Inverter inverter is compatible with the SolarMan app, via a Wifi or GSM 

data logger (See SolarMan instruction manual).

APPENDIX D

If an external Residual Current Device (RCD) is used it should be of Type A/AC with a tripping current of 30mA 

or higher.

Use of RCDs 

Residual Current Devices (RCDs): An RCD dedicated for an Inverter Energy System (IES) may be used to meet 
the mechanical cable protection requirements of AS/NZS3000 for the cable from the switchboard to the IES. 
If an RCD is installed the engineer must: 

1.  Disconnect all live conductors (including both active and neutral conductors) and 
2. 

Be of the type specified in the inverter manufacturer’s instructions or as labelled on the inverter. 

We recommend the use of an RCD on all circuits and sub-circuits connected to the Sunsynk Inverter. Below 
is the specifications for a Residual Current Breaker with Overcurrent Protection (RCBO)

BMS 485 Port

Can Port

WIFI/RS232

Summary of Contents for ECCO SUN-3.6K-SG05LP1-EU








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands