SunSynk ECCO SUN-3.6K-SG05LP1-EU User Manual Download

Page: 33 / 71

ECCO SG04LP1 | User Manual

5. OPERATION

5.1. Display

LED indicator

Meaning

Green LED solid light

PV connection normal

Green LED solid light

Grid connection normal

Normal

Green LED solid light

Inverter functioning normally

Alarm

Red LED solid light

Fault

Function Key

Description

Esc

To exit the previous mode

Increase the value of a setting

Down

Decrease the value of a setting

Enter

Confirm setting change (If not pressed each time the setting will not

be saved)

5.2. Switching ON/OFF

Once the inverter has been correctly installed and the batteries have been connected, press the ON/OFF

button (located on the left side of the case) to activate the system.

When the system is connected without a battery but connected with either PV or grid and the ON/OFF but-

ton is switched off, the LCD will still illuminate (display will show off). In this condition, when switching on the

ON/OFF button and selecting ‘No Battery’, the system can still work.

Summary of Contents for ECCO SUN-3.6K-SG05LP1-EU








































































Search results

Summary of Contents for ECCO SUN-3.6K-SG05LP1-EU

Reviews:

Related manuals for ECCO SUN-3.6K-SG05LP1-EU

Brands by name

Popular brands

SunSynk ECCO SUN-3.6K-SG05LP1-EU, User Manual

Search results

Summary of Contents for ECCO SUN-3.6K-SG05LP1-EU

Reviews:

Related manuals for ECCO SUN-3.6K-SG05LP1-EU

Brands by name

Popular brands