SunSynk ECCO SUN-3.6K-SG05LP1-EU User Manual Download | Manualshive

Page: 43 / 71

background image

ECCO SG04LP1 | User Manual

43

What this page displays:

Inverter shutdown voltage set as either a voltage or %.

Inverter low battery warning set as either a voltage or %.

Restart voltage set as either a voltage or %.

What you can do from this page:

Adjust battery shut down (voltage or %)

Adjust low battery warning (voltage or %)

Adjust restart (voltage or %)

PLEASE NOTE

Activating Shutdown causes the inverter to enter standby-mode. It does not entirely shut down the

inverter. Total shutdown occurs at voltages below 19V.

The voltage displayed on the Sunsynk Parity Inverter will vary depending on whether the inverter is charging
or discharging the batteries.

Since the batteries are 48V, the figure on the left is x4:

Fully Charged 50.54V (Discharge Mode)

Fully Charged 58.50V (Charge Mode)

75% Charged 49.60V (Discharge Mode)

75% Charged 54.80V (Charge Mode)

25% Charged 48.00V (Discharge Mode)

25% Charged 50.80V (Charge Mode)

Completely Discharged 47.50V

Setting the cut-off higher is better for the batteries.

«
...
41
42
43
44
45
...
»

Summary of Contents for ECCO SUN-3.6K-SG05LP1-EU








































































Reviews:

No comments

Related manuals for ECCO SUN-3.6K-SG05LP1-EU

Brand: Sonoro Pages: 148

Brand: VOLTCRAFT Pages: 10

Brand: JTS Pages: 8

Brand: CYP Pages: 60

Brand: Goodwe Pages: 50

Brand: Alca Power Pages: 8

Brand: Xantrex Pages: 124

Brand: Omnitron Systems Technology Pages: 1

Brand: Black Box Pages: 12

Brand: RDZ Pages: 60

Brand: Mitsubishi Pages: 96

Symo Hybrid 3.0-3-S

Brand: Fronius Pages: 140

Brand: Yangzhou Shenzhou Wind-driven Generator Pages: 35

Brand: NSK Pages: 52

Brand: Generac Power Systems Pages: 4

Brand: Linear Technology Pages: 6

Brand: ICP DAS USA Pages: 2

Brand: Denon Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands