Sun Microsystems Netra CT 820 Service Manual Download Page 96

Page: 96 / 132

A-12

Netra CT 820 Server Service Manual

• July

2004

Note –

The external Ethernet interface on the distributed management card and the

external Ethernet interface on the switching fabric board must be connected to
different subnets. If they are configured on the same subnet,

arp

messages will be

displayed on the distributed management card console.

Following are the pinouts for each of the ports on the switching fabric board:

■

“10/100 Mbps Ethernet Ports (20–23) Pinouts” on page

■

“1000 Mbps Ethernet Ports (25 and 26)” on page

■

“Console Port” on page

A.4.1

10/100 Mbps Ethernet Ports (20–23) Pinouts

The Ethernet ports 20-23 on the rear transition module for the switching fabric board
use standard RJ-45 connectors. They are all 10/100 Mbps Ethernet ports.

FIGURE

A-11

RJ-45 Ethernet Connector Diagram

TABLE

A-8

10/100Mb Switched Ethernet Port Pinout

Pin No.

Signal

Pin No.

Signal

RX+

—

RX-

TX-

TX+

—

1 2 3 4 5 6 7 8

Summary of Contents for Netra CT 820





































































































































Search results

Summary of Contents for Netra CT 820

Reviews:

Related manuals for Netra CT 820

Brands by name

Popular brands

Sun Microsystems Netra CT 820, Service Manual

Search results

Summary of Contents for Netra CT 820

Reviews:

Related manuals for Netra CT 820

Brands by name

Popular brands