manualshive.com logo in svg

Stryker The Go BED FL17E, Maintenance Manual, Page: 3 / 64

Share
Download
Stryker The Go BED FL17E Maintenance Manual Download Page 3

TABLE OF CONTENTS

 

 

1. INTRODUCTION....................................................................................................................................... 5

 

1.1   BED SPECIFICATIONS .................................................................................................................. 5

 

1.2   TECHNICAL SUPPORT .................................................................................................................. 5

 

1.3   SAFETY ........................................................................................................................................... 6

 

Warning / Caution / Note Definition ................................................................................................ 6

 

Safety Tips and Guidelines ............................................................................................................. 6

 

Static Discharge Precautions.......................................................................................................... 8

 

1.4   WARRANTY .................................................................................................................................... 8

 

Limited Warranty............................................................................................................................. 8

 

To Obtain Service and/or Parts ...................................................................................................... 8

 

To Require Service

...................................................................................................................... 8

 

To Order Parts

.............................................................................................................................. 9

 

Return Authorization ..................................................................................................................... 10

 

Damaged Merchandise................................................................................................................. 10

 

1.5   SET-UP PROCEDURE.................................................................................................................. 10

 

Checklist ....................................................................................................................................... 10

 

1.6   BED ILLUSTRATION..................................................................................................................... 12

 

2. PREVENTIVE MAINTENANCE.............................................................................................................. 13

 

2.1   BED CLEANING AND MATTRESS CARE.................................................................................... 13

 

Cleaning Beds............................................................................................................................... 13

 

Bed Mattress Care ........................................................................................................................ 13

 

2.2   LUBRICATION............................................................................................................................... 14

 

Annual Checklist ........................................................................................................................... 14

 

Two Years Time Interval Checklist ............................................................................................... 14

 

Five Years Time Interval Checklist ............................................................................................... 14

 

Lubrication Points Illustrated......................................................................................................... 15

 

2.3   PREVENTIVE MAINTENANCE PROGRAM ................................................................................. 16

 

Checklist ....................................................................................................................................... 16

 

PC Board Maintenance Program.................................................................................................. 17

 

Recommended Spare Parts ......................................................................................................... 18

 

3. TROUBLESHOOTING............................................................................................................................ 19

 

3.1   TROUBLESHOOTING GUIDE ...................................................................................................... 19

 

4. MAINTENANCE PROCEDURES ........................................................................................................... 24

 

4.1   SIDE-RAIL ASSEMBLY REPLACEMENT..................................................................................... 24

 

Foot Side-Rail Assembly Replacement ........................................................................................ 24

 

Head Side-Rail Assembly Replacement....................................................................................... 25

 

4.2   SIDE-RAIL REPLACEMENT (RAIL ONLY) ................................................................................... 27

 

Foot Side-Rail Replacement (Rail Only)....................................................................................... 27

 

Head Side-Rail Replacement

 

(Rail Only) ..................................................................................... 27

 

4.3   MEMBRANE REPLACEMENT (FOOT BOARD CONTROL PANEL) ........................................... 28

 

4.4   MEMBRANE REPLACEMENT ( SIDE-RAIL CONTROL) ............................................................. 29

 

4.5   NURSE CALL SYSTEM COMPONENT REPLACEMENT............................................................ 30

 

4.6   FOOT BOARD CONNECTOR REPLACEMENT........................................................................... 32

 

4.7   FOOT END CASE CONNECTOR REPLACEMENT ..................................................................... 33

 

4.8   PC BOARD REPLACEMENT ........................................................................................................ 34

 

4.9   ON/OFF SWITCH REPLACEMENT .............................................................................................. 35

 

Summary of Contents for The Go BED FL17E

































































Reviews:

No comments