Stryker The Go BED FL17E Maintenance Manual Download Page 18

Page: 18 / 64

Chapter 2

The

BED Maintenance Manual

Recommended Spare Parts

The following is a list of recommended on hand spare parts for the

BED.

Electronic/Electrical Assembly Parts

PC Board

QDF14-0990

PC Board stand off pins

QDF8011

Strain relief bushing

QPNC0604

S.A. power cord 120V/Connector

QDF17-0236/QDF8042

Micro switch

1325P003

Night light

QDF9539

Actuator Assembly Parts

Hi-lo actuator

QDF17-0005

Knee Gatch actuator

QDF17-0006

Head actuator

17-0041

Control Panel Assembly Parts

Nurse control plate and membrane

QDF17-0180/QDF17-0127

S.A. Fixed 3 way patient control (H-B-F)

13-0220

S.A. Fixed 3 way patient control (F-B-H)

13-0221

S.A. Fixed 2 way patient control (F-H)

17-0193

S.A. Fixed 2 way patient control (H-F)

17-0194

Side-Rail assembly parts

Head side-rail protector

17-0220

Foot side-rail protector

17-0221

3M adhesive tape #950 x 1"

QDF7826

Side-rail right handed release

17-0306-P

Side-rail left handed release

17-0307-P

Dome cap DP1250 1-1/4"

QDFP1514

Protective cap

QPN-18748

Mattress support Assembly

Warm grey mattress retainer

QPN-14034-2

Base Assembly Parts

"Tente" caster with locking system

RT61C

"Tente" caster without locking system

T61CSW

5th wheel

RL5

Pedal green treadle tip

QPN-18028

Pedal red treadle tip

QPN-18029

Anchor washer for 3/16 dia. stud

VW00A06

Rue ring cotter dia. 3/8" p.z.

QDF7878

Miscellaneous

OG-2 grease

M0027

Tread locker - medium strength (blue)

M008

"Sand Grey" aerosol spray paint

DDCAP-GSP

Summary of Contents for The Go BED FL17E

































































Search results

Summary of Contents for The Go BED FL17E

Reviews:

Stryker The Go BED FL17E, Maintenance Manual, Page: 18 / 64

Search results

Summary of Contents for The Go BED FL17E

Reviews: