manualshive.com logo in svg

Stryker The Go BED FL17E, Maintenance Manual, Page: 23 / 64

Share
Download
Stryker The Go BED FL17E Maintenance Manual Download Page 23

 

Troubleshooting 

Chapter 3 

 

23 

PROBLEM 

POSSIBLE CAUSES 

RECOMMENDED ACTION 

 

Nurse call switch defective. 

Replace nurse call switch 
(see section 4.5). 

 

Nurse call switch cable 
defective 

Replace nurse call cable 
(see section 4.5) 

Safety side-rails jam, move 
with difficulty, do not latch in 
high position or latch with 
difficulty. 

Side-rail mechanisms poorly 
greased and/or mechanism 
parts loosened. 
 

Apply grease on the side-
rail plungers, plunger 
springs, arm glide rods and 
rail shafts (see  section 2.2, 
"Lubrication"). Check all 
applicable hardware and 
parts alignment. Replace 
parts as needed (see 
section 4.1). 

 

Side-rail parts misaligned 
following a blow. 

Replace side-rail assembly 
(see section 4.1)  

Brake does not engage when 
activated or do not release. 

Fasteners of the brake 
activation mechanism not 
secured or parts misaligned. 

Check all applicable 
linkage, hardware and parts 
alignment. Replace parts 
as needed (see sect. 4.19, 
"Brake/steer pedal…") 

 

One or both casters that are 
part of the locking mechanism 
defective. 

Replace caster (see section 
4.21). 

Steer wheel (5th wheel) does 
not engage when activated or 
does not disengage. 

Fasteners of the 5th wheel 
activation mechanism not 
secured or parts misaligned. 

Check all applicable 
linkage, hardware and parts 
alignment. Replace parts 
as needed (see sect. 4.20). 

 

Swing arm assembly spring 
warped 

Replace the 5th wheel 
swing arm assembly (see 
section 4.20) 

Summary of Contents for The Go BED FL17E

































































Reviews:

No comments