manualshive.com logo in svg

Stratasys V650 Flex, Site Preparation Manual, Page: 3 / 24

Share
Download
Stratasys V650 Flex Site Preparation Manual Download Page 3

Page iii

Contents

Revision Log ................................................................................................. iv
Safety............................................................................................................  iv

Safe Environment................................................................................................................ iv

About the V650 Flex Printer........................................................................... 1

Components ........................................................................................................................  1
How to Use This Guide........................................................................................................  2

Site Prep Tasks.............................................................................................. 2

Selecting the Site ................................................................................................................  2
Physical Specifications and Space Requirements ..............................................................  3
Environmental Requirements ..............................................................................................  7
Electrical Requirements ......................................................................................................  9
Controller and Workstation Requirements.........................................................................  10
LAN Requirements ............................................................................................................  10

Receiving the Printer ................................................................................... 11

Inspect Crate for Damage .................................................................................................. 11

Preparing For Installation............................................................................. 11

Required Tools and Equipment .......................................................................................... 11
Unpacking the Printer........................................................................................................  12
Unpacking the Resin Vat ...................................................................................................  18

Site Preparation Checklist ........................................................................... 19

Electrical Installation Requirements ..................................................................................  19
Environmental Requirements ............................................................................................  19
Required Installation Tasks................................................................................................  19

Summary of Contents for V650 Flex

























Reviews:

No comments