Stihl FR 131 T Instruction Manual Download Page 31

Page: 31 / 44

FR 131 T

English

If the engine is down on power,

difficult to start or runs poorly at idle

speed, first check the spark plug.

Fit a new spark plug after about 100

operating hours – or sooner if the

electrodes are badly eroded. Install

only suppressed spark plugs of the

type approved by STIHL – see

"Specifications".

Removing the Spark Plug

Remove the cover (1).

Pull off the spark plug boot (2).

Unscrew the spark plug (3).

Checking the Spark Plug

Clean dirty spark plug.

Check electrode gap (A) and

readjust if necessary – see

"Specifications".

Rectify the problems which have

caused fouling of the spark plug.

Possible causes are:

–

Too much oil in fuel mix.

–

Dirty air filter.

–

Unfavorable running conditions.

WARNING

Arcing may occur if the adapter nut (1) is

loose or missing. Working in an easily

combustible or explosive atmosphere

may cause a fire or an explosion. This

can result result in serious injuries or

damage to property.

Use resistor type spark plugs with a

properly tightened adapter nut.

Installing the Spark Plug

Screw the spark plug (3) into the

cylinder.

Tighten down the spark plug (3) with

the combination wrench.

Press the boot (2) firmly onto the

spark plug.

Fit the cover (1) and screw it down

firmly.

Spark Plug

0000-GXX 0537-A0

000BA039 KN

000BA045 KN

Summary of Contents for FR 131 T













































Search results

Summary of Contents for FR 131 T

Reviews:

Related manuals for FR 131 T

Brands by name

Popular brands

Stihl FR 131 T, Instruction Manual

Search results

Summary of Contents for FR 131 T

Reviews:

Related manuals for FR 131 T

Brands by name

Popular brands