manualshive.com logo in svg

Steelcase 800 Series, Manual

Share
Download
Steelcase 800 Series Manual Download Page 27

Page 27 of 27

939501617 Rev V

5b

5b

5c

5c

5a

NOSE OF
TETHER

TOP VIEW

1/2" GAP

PUSH

BEAM

IMPORTANT!

5. 

Tether the case to the beam.

 

a) Push the case so that the nose of the

 

storage to beam tether slides between

 

the underside of the beam and top

 

side of beam cover.

 

b) It may be necessary to slide the

 

case left or right to engage the actuator

 

portion of the storage to beam tether.

 

c) 

IMPORTANT STEP:

 Pull the storage

 

unit on the left side, then the right side

 

to confirm that the storage unit is

 

secured to the beam.

CAUTION:

 Failure to secure the 

case to the beam could result in an 
unstable condition where the case 
could tip causing personal injury.

DEPRESS THE
ACTUATOR PAD

TETHER BRACKET

7a

BEAM

CASE

6. 

Reinstall the drawers (see pages 6 

or 7).

7. 

Removal of a tethered case from

the beam.

 

a) Depress the left actuator pad

 

with a long narrow object.

 

b) Pull the left side of the case

 

away from the beam by a couple

 

of inches.

 

c) Repeat steps (a) and (b) on the

 

right side.

SIDE VIEW

TOP VIEW

BEAM

7b

Summary of Contents for 800 Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands