manualshive.com logo in svg

Steelcase 800 Series, Manual

Share
Download
Steelcase 800 Series Manual Download Page 22

Installing Glass Doors

 

CAUTION: 

 This is tempered

 

glass.  Doors will shatter if

 

casually impacted on hard 

surfaces.  Do not set edges of glass on 
hard surfaces such as concrete.  Hold 
glass at the edges, not the hinges.
While one person can do the glass 
installation and removal, it is strongly 
recommended that a second person 
assists by supporting the glass while
the hinges are engaged and disengaged.  

NOTE:

  If any counterweights are to be 

used, they must be installed before 
installing the glass doors.

NOTE: 

 Flush mounted doors use the 

rear set of holes. Proud mounted doors 
use the forward set of holes.

1.

  Adjust shelves to desired positions.

2.

  Insert hinge plate spacer and 

assemble all hinge mounting plates to
the uprights with two (2) or four (4) 
screws each hinge and tighten.

3.

  Position door and snap hinges onto 

hinge plates.  

NOTE:

  It may be necessary to adjust the 

vertical position using the adjustment 
screw on the hinge plate so that all 
hinges will snap in easily.

2

FLUSH
MOUNT
VERSION

HINGE

PLATE

SPACER

2

PROUD
MOUNT
VERSION

HINGE

PLATE

SPACER

HINGE

MOUNTING

PLATE

PIVOT PIN

SLOT FOR

PIVOT PIN

3a

CLICK!

3b

Page 22 of 27

939501617 Rev V

Summary of Contents for 800 Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands