Star Headlight & Lantern LCS850MG, Installation And Instruction Manual

Page: 39 / 64

-32-
Installation: Detailed Programming
Logic Controlled TD Programming:
Output Select and Polarity
By default, when you select to use a LOGIC controlled TD, the output wires will 12VDC (see
Traffic
Directors with Built-In Controllers
on page 13).
If instead, you would like the outputs to be grounded, change this setting.
PB4 is Green : (Default setting) The LOGIC outputs described on page 13 will 12vdc.
PB4 is Red : The LOGIC outputs described on page 13 will output Ground.
2-WIRE LOGIC + POWER 3-WIRE INDEPENDENT LOGIC
P
O
W
E
R
/C
E
N
T
E
R
-O
U
T
L
E
F
T
R
IG
H
T
W
A
R
N
L
E
F
T
R
IG
H
T
CENTER-OUT= LEFT+RIGHT
LEFT=
RIGHT=
-
LEFT+POWER/CENTER-OUT
RIGHT+POWER/CENTER-OUT
NO WARN
PB5 PB14
LEFT+POWER/WARN
RIGHT+POWER/WARN
CENTER-OUT+POWER/WARN LEFT=
RIGHT=
CENTER-OUT=
3-WIRE LOGIC + POWER
(DL15-30W)
L
E
F
T
(Y
e
ll
o
w
)
P
O
W
E
R
/W
A
R
N
(R
e
d
)
C
E
N
T
E
R
-O
U
T
(
P
u
rp
le
)
G
R
O
U
N
D
-O
p
ti
o
n
a
l
(B
la
c
k
)
PB13
R
IG
H
T
(G
re
e
n
)
DEFAULT
As indicated on page 6, page 13, and above, the LCS850MG has the ability to operate a Traffic Director
(arrowstick) that has a built in controller (i.e. uses LOGIC controls). It can be programmed to operate
sticks with three different input requirements:
By default, when you set Control Head DIP switch #8 (DISCRETE TD) up (to use a LOGIC controlled TD),
the output of the wires will control our DL15-30W (see center diagram above)
.
If your arrowstick operates differently, program the output as described below:
During programming, PB5, PB13, PB14 buttons will operate as “radio” type buttons (only one can be
active at any time). Depressing (activating) one button will change it to RED and will deactivate the other
two buttons (change them to GREEN).
PB5 is Red : The LOGIC outputs will be set for 3-WIRE INDEPENDENT.
PB13 is Red : (Default setting) The LOGIC outputs will be set for 3-WIRE+POWER.
PB14 is Red : The LOGIC outputs will be set for 2-WIRE+POWER.
Once you have programmed all necessary options, you must flip
the Programming Mode DIP switch down to save the changes.
Once you have programmed all necessary options, you must flip
the Programming Mode DIP switch down to save the changes.
Logic Controlled Traffic Director Programming
The two options described below ONLY apply if you have set Control Head DIP switch #8 (DISCRETE TD)
for a LOGIC controlled traffic director
(see page 6) . That DIP switch MUST be in the up position to use this
option.
Logic Controlled Output Select
Logic Controlled Traffic Director Polarity
Programming Mode DIP Switch: Up
Slide Switch:
1 1 1 1
Audio Mode Buttons (HF/WAIL/YELP/PHSR/RADIO): All OFF/Green
And modify these buttons: PB5, PB13, PB14
Programming Mode DIP Switch: Up
Slide Switch:
1 1 1 1
Audio Mode Buttons (HF/WAIL/YELP/PHSR/RADIO): All OFF/Green
And modify this button: PB4
All of the options on pages 17
All of the options on pages 17 All of the options on pages 17
All of the options on pages 17----34 can optionally be programmed using free software and a
34 can optionally be programmed using free software and a 34 can optionally be programmed using free software and a
34 can optionally be programmed using free software and a
USB to serial cable (P/N SUSB USB to serial cable (P/N SUSB USB to serial cable (P/N SUSB USB to serial cable (P/N SUSB----850MG) available upon request from StarSignal at 585 850MG) available upon request from StarSignal at 585 850MG) available upon request from StarSignal at 585 850MG) available upon request from StarSignal at 585----226 226 226 226----9787. 9787. 9787. 9787.