manualshive.com logo in svg

Standard IGL15, Operation And Maintenance Manual, Page: 7 / 45

Share
Download
Standard IGL15 Operation And Maintenance Manual Download Page 7

      IGL15 Spare parts replacement manual

 

Version

：

S2018.05 

6   

 

3.

 

Lift  the  tractor  into  a  vertical  position  with  lifting  equipment  and  rotate  the 

traction  wheel  for  more  than  1  week.Testing  with  dial  indicator:  the  normal 

runout  of  the  groove  surface  of  the  traction  wheel  is 

≤

0.12mm.  Meanwhile, 

components are required: the rotor rotates flexibly, the bearing has no noise, and 

the rotor and stator have no interference. 

4.

 

Screw  the  thin  nut  M12  with  screw  M12×55,  and  put  it  into  the  corresponding 

screw  hole  on  the  end  face  of  the  machine  base  together  with  washer  12  (the 

screw is screwed to a depth of about 20mm). Lock with an open wrench (18mm); 

Install  the baffle rod to  screw M12×55,  fix it with nut  M12  and washer 12, and 

tighten it with open spanner (18 mm). 

 

5.

 

The whole traction machine is electrified for test run. 

 

Bolt M12×40 

Washer 12 

Screw M12 x 55 

Thin nut M12 

Washer 12 

Rope rod 

Washer 12 

Nut M12 

Summary of Contents for IGL15














































Reviews:

No comments