manualshive.com logo in svg

Standard IGL15, Operation And Maintenance Manual, Page: 3 / 45

Share
Download
Standard IGL15 Operation And Maintenance Manual Download Page 3

      IGL15 Spare parts replacement manual

 

Version

：

S2018.05 

2   

1.

 

Preface 

1.1. Safety Declaration 

Only qualified personnel are allowed to perform  any planning, installation 

or maintenance work to GTW7 series gearless PMS elevator traction machines.   

The  personnel  must  be  trained  for  the  job  and  must  be  familiar  with  the 

installation,  assembly,  commissioning  and  operation  of  the  product.  Sufficient  knowledge  in  lift 

construction is essential. Their commissioning is prohibited until the requirements of the directive 

are satisfied by or upon integration of the motor into the final product.   

The  regulations  concerning  operation,  maintenance  and  inspection  in  accordance  with  the 

applicable  safety  regulations  in  lift  construction  such  as  GB  7588-2003  “Safety  rules  for  the 

construction  and  installation  of  electric  lifts”  (equal  to  EN81-1:  1998)  and  other  relevant. 

Regulations shall be strictly observed.   

The  operator is responsible for the proper installation  of  the gearless PMS elevator traction 

machines  with  regard  to  safety  requirements  as  well  as  for  its  inspection  and  maintenance  as 

specified  in  the  applicable  regulations.  No  liability  can  be  assumed  for  any  damage  caused  by 

improper handling or any other acts, which are not in conformity with these operating instructions 

and thus deter from the qualities of the product.

 

1.2. IGL15 traction machine spare parts list 

NO. 

Part No. 

Name 

QTY 

Remark 

1 

IGL15.1.1-1 

Traction Wheel 

1 

 

2 

ERN1387 

OIH100 

Encoder 

1 

Selectable 

3 

Bearing 

GT/T276 

Bearing 6213-2RS 

1 

Main Shaft 

Bearing 

4 

Bearing 

GB/T276 

Bearing 6317-2RS/C3 

1 

Main Shaft 

Bearing 

5 

GTW7.2.1 

FZD10 Brake 

2 

Brake 

6 

GTW7.2.1.1 

Brake Piece part 

2 

 

7 

KCB_R-5 

Basket Switch 

1 

For Hand Wheel 

Summary of Contents for IGL15














































Reviews:

No comments