manualshive.com logo in svg

Standard IGL15, Operation And Maintenance Manual, Page: 25 / 45

Share
Download
Standard IGL15 Operation And Maintenance Manual Download Page 25

      IGL15 Spare parts replacement manual

 

Version

：

S2018.05 

24   

 

8.

 

Install  corrugated  washer  120  and  encoder  cover  (refer  to  IGL15  permanent 

magnet  synchronous  elevator  tractor  spare  parts  replacement  manual  -  bearing 

6213-2rs replacement method). 

9.

 

Install  encoder  (refer  to  IGL15  permanent  magnet  synchronous  elevator  spare 

parts replacement manual - encoder replacement method). 

10.

 

Install  brakes  (refer  to  IGL15  permanent  magnet  synchronous  elevator  tractor 

spare parts replacement manual - brake replacement and adjustment method). 

11.

 

Install  protective  cover  or  rope  bar  (refer  to  IGL15  permanent  magnet 

synchronous  elevator  tractor  spare  parts  replacement  manual  -  tractor  wheel 

replacement method). 

12.

 

Power on the whole traction machine and run the whole machine test. 

 

 

 

Gland 

Screw M8 x 25 

Summary of Contents for IGL15














































Reviews:

No comments