background image

ASSEMBLY INSTRUCTIONS

7

STEP 4

There is a 

"L"

 decal on the 

LEFT PIVOT ARM(7), 

and a 

"R"

 decal on the 

RIGHT PIVOT ARM(8).

Refer to the Inset drawing.  Insert the 

LINKAGE(16)

 through the bracket on the 

RIGHT FRONT FRAME(2),

then attach the 

LINKAGE(16)

 to the 

RIGHT PIVOT ARM(8) 

with 

NYLOCK NUT(M8)(64).  DO NOT

OVER TIGHTEN THE NUT.

Attach the 

RIGHT PIVOT ARM(8)

 onto the 

RIGHT FRONT FRAME(2)

 by sliding the slots in the end of

the 

RIGHT PIVOT ARM(8)

 into the slot on the 

RIGHT FRONT FRAME(2).

  Repeat on other side.

STEP 5:  

Place the 

BACK FRAME(9)

 between the Brackets of the 

LEFT

 and 

RIGHT PIVOT ARMS(7,

8)

 and secure with 

BUTTON HEAD BOLTS(M8 x 60mm)(61), NYLOCK NUTS(M8)(64),

 and

WASHERS(M8)(67).

STEP 6:  

Attach the 

SEAT FRAME(12)

 onto the 

BACK FRAME(9)

 with 

BUTTON HEAD BOLTS

(M8 x 60mm)(61), NYLOCK NUT(M8)(64),

 and

 WASHERS(M8)(67).

SEAT FRAME HEIGHT ADJUSTMENT

There are adjustment holes on the 

BACK FRAME(9)

 allowing you to position the 

SEAT FRAME(12)

 at

three different heights.  In the highest position, it is easier to invert but more difficult to recover from inversion.
In the lowest position, it is more difficult to invert but easier to recover from inversion.  Tall people may prefer
the lowest position and shorter people may prefer the highest position.

L

R

Summary of Contents for CoreTraining Inversion System























Reviews: