background image

Page | 18 

 
SECTION 6   

 

Maintenance 

 
There are no wear items in the MBS that require periodic replacement.  However, regular 
care will assure maximum availability of power.   
Keep the ventilation openings in the cabinet free of dust and debris. 
 
Wipe the cabinet exterior with a soft cloth, slightly dampened with water, to remove dust. 
 
Consider performing periodic infrared temperature measurements on the circuit breaker 
terminations.  This will require access to the cabinet interior.  There are hazardous voltages 
present and any work must be performed using caution.  Only trained service personnel 
should perform this work.  Elevated temperatures of the terminations usually are the sign of 
a loose connection, but can also signal that a breaker is failing.  Loose connections should 
only be serviced after removal of power. 
 
If the system is powered down, consider removing accumulated dust from the cabinet 
interior using a vacuum cleaner. 
 
 
 

SECTION 7 

 

 FirstLine P Maintenance Bypass Switch Technical Specifications 

 

Table 9 - Technical Specifications 

 

Environmental 

 

 

 

Altitude 

De-rate load capability above 1000 meters 1% per 100 

meters. 

Operating Temperature 

40

o

 C Maximum 

Humidity 

Maximum 95%RH, Non-condensing 

 

Electrical                                                                                                                                                             

160 kVA

 

200 kVA

 

250 kVA

 

Rated voltage 

480/277 

480/277 

480/277 

Rated Current 

212A 

265A 

331A 

Breaker Rating 

300A 

350A 

450A 

Minimum Wire Size         INPUT 

500 kcmil or   

(2) 2/0 AWG 

(2) 3/0 AWG 

(2) 300 kcmil 

                                      OUTPUT 

300 kcmil 

500 kcmil or   

(2) 2/0 AWG 

(2) 4/0 AWG 

Heat Rejection – Less than  (BTU/Hr) 

800 

1000 

1250 

 

 

 

Summary of Contents for FLU-160-00





















Reviews: