background image

Page | 3 

 
SECTION 2  

 

SAFETY WARNINGS 

 

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 

 

READ AND FOLLOW ALL SAFETY INSTRUCTIONS 

 

  Do not use outdoors. 

  Do not route wiring across or near hot surfaces. 

  Do not install near gas or electric heaters. 

  Equipment should be installed where it will not readily be subjected to tampering by 

unauthorized personnel. 

  The use of accessory equipment not recommended by the manufacturer may cause 

an unsafe condition. 

  Do not use this equipment for other than intended use. 

  This equipment connects to the output of an uninterruptible power supply.  

Hazardous voltages may be present even when the electrical supply to this 
equipment is turned off. 

  If equipped with a maintenance bypass switch, control connections between this 

equipment and the ups must be present to prevent the possibility of backfeed. 

  Read and follow the instructions that came with the associated UPS or emergency 

lighting system before operating this equipment. 

 
 

DANGER 

 
This equipment contains lethal voltages.  All repairs and service should only be performed 
by authorized service personnel.  There are no user serviceable parts inside this 
equipment.  Operation of switches and breakers require access to the cabinet interior and 
should only be performed by qualified personnel exercising appropriate caution. 
 

WARNING 

 
This equipment connects to the output of a UPS which contains its own energy source 
(batteries).  The UPS output may carry live voltage even when the UPS is not connected to 
an AC supply. 
 
To reduce the risk of fire and electric shock, install this equipment in a humidity controlled, 
indoor environment, free of conductive contaminants.  Do not operate near water or 
excessive humidity (95% maximum).  If condensation is present, the equipment must be 
allowed to completely dry before operation. 
 

 

Summary of Contents for FLU-160-00





















Reviews: