background image

Page | 5 

 
SECTION 3   

 

Cabinet Setup 

 
This SECTION describes: 

 

Equipment inspection 

 

Floor loading and clearances 

 

Removing and replacing the cabinet panels 

 

Unloading the cabinet(s) 

 

Attaching the cabinet to the UPS 

 

Inspecting the Equipment 

 
If any equipment has been damaged during shipment, keep the shipping and packing 
materials for the carrier or place of purchase and file a claim for shipping damage. If you 
discover damage after acceptance, file a claim for concealed damage. 
 
To file a claim for shipping damage or concealed damage: 1) File with the carrier within 15 
days of receipt of the equipment, 2) Send a copy of the damage claim within 15 days to your 
service representative. 
 

Floor Loading 

 
When planning the installation, consider the cabinet weight for floor loading. The strength of 
the installation surface must be adequate for point and distributed loading. The approximate 
weights are shown in the following table. 
 

Table 2 - Model Floor Loadings 

 

STANDARD MODEL FLOOR LOADING 

 

kVA 

MAXIMUM WEIGHT 

POINT LOADING 

160 

390 lbs (177 kg) 

6.5 lb/in

2

 (0.5 kg/cm

2

200 

390 lbs (177 kg) 

6.5 lb/in

2

 (0.5 kg/cm

2

250 

390 lbs (177 kg) 

6.5 lb/in

2

 (0.5 kg/cm

2

 

CLEARANCES 

 
The following clearances are recommended for the FirstLine P Maintenance Bypass Switch 
Cabinet. 
 

From Front of Cabinet 

36” (91.4 cm) working space 

 
 
 
 
 
 
 

Summary of Contents for FLU-160-00





















Reviews: