background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SC On-line UPS   

 

 

User’s Manual 

Rack / Tower Models   

700VA to 3kVA, 120Vac 

 

 

© 2016 Falcon® Electric, Inc. All rights reserved. 

All other brand names and trademarks are the property of their respective owners. 

The information stated in this document is subject to change without notice. 

Falcon®, Falcon® Electric and UPS logos are registered trademarks of Falcon Electric, Inc.   

OM480039 SC1-3KR_T 120V_12-12-16 REV.NR 

 

Proprietary: The information contained herein is proprietary to Falcon Electric, Inc. and 

shall not be reproduced or disclosed in whole or in part or used for any reason except 

when such user possesses direct, written authorization from Falcon Electric, Inc. 

 

The statements contained herein are based on good faith assumptions and provided for 

general information purposes only. These statements do not constitute an offer, promise, 

warranty or guarantee of performance. Actual results may vary depending on certain 

events or conditions. This document should not be used or relied upon for any purpose 

other than that intended by Falcon Electric, Inc. 

Summary of Contents for SG700RM-1SC











































Reviews: