background image

This is information on a product in full production. 

March 2015

DocID022729 Rev 5

1/70

L6472

Fully integrated microstepping motor driver

Datasheet 

-

 production data

Features

Operating voltage: 8 - 45 V

7.0 A output peak current (3.0 A 

r.m.s.

)

Low R

DS(on)

 power MOSFETs

Programmable speed profile

Programmable power MOSFET slew rate

Up to 1/16 microstepping

Predictive current control with adaptive decay

Non dissipative current sensing

SPI interface

Low quiescent and standby currents

Programmable non dissipative overcurrent 
protection on all power MOSFETs

Two levels of overtemperature protection

Applications

Bipolar stepper motor

Description

The L6472 device, realized in analog mixed 
signal technology, is an advanced fully integrated 
solution suitable for driving two-phase bipolar 
stepper motors with microstepping. It integrates 
a dual low R

DS(on)

 DMOS full bridge with all of the 

power switches equipped with an accurate on-
chip current sensing circuitry suitable for non 
dissipative current control and overcurrent 
protection. Thanks to a new current control, 
a 1/16 microstepping is achieved through an 
adaptive decay mode which outperforms 
traditional implementations. The digital control 
core can generate user defined motion profiles 
with acceleration, deceleration, speed or target 
position, easily programmed through a dedicated 
register set. 

All application commands and data registers, 
including those used to set analog values 
(i.e.: current control value, current protection trip 
point, deadtime, etc.) are sent through a standard 
5-Mbit/s SPI.

A very rich set of protections (thermal, low bus 
voltage, overcurrent) makes the L6472 device 
“bullet proof”, as required by the most demanding 
motor control applications.

          

HTSSOP28

POWERSO36

Table 1. Device summary 

Order codes 

Package 

Packing 

L6472H HTSSOP28

Tube 

L6472HTR HTSSOP28

Tape 

and 

reel 

L6472PD

POWERSO36

Tube

L6472PDTR POWERSO36 Tape 

and 

reel

www.st.com

Summary of Contents for L6472







































































Reviews: