background image

3

!

Please read and understand these 
instructions completely before 
installation to avoid possible injury,  
or damage to the accessory or vehicle. 

WARRANTY INFORMATION:

All SSV Works enclosures are covered by a limited lifetime warranty against defects in material 
or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against 
defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year 
warranty against defects in material or workmanship. All Kicker Speakers are covered by a 
limited 1 year warranty against defects in material or workmanship. Labor for replacement of 
defective components is not covered. Contact SSV Works for further warranty information.

Glove Box Subwoofer Enclosure

9.   B-H1173 Audio Signal 

Extension Cable - 3ft

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030

www.SSVworks.com     |     Phone: 818-991-1778     |     Fax: 866-293-6751

PARTS LIST IMAGES

3.   Glove Box Door Bracket

4.   Lower Mounting Bracket 

with #14 Screw x1 each

2.   8mm Socket Head Screws & 

Washers x14

5.   Flat Mounting Bracket “A”

6.   Mounting Bracket “B”

1.    RZ4-GB10 Enclosure 

(door not included)

7.   Left & Right Door Hinge 

Brackets

8.   M6 x 8mm (T30 torx) Screw 

x2

TOOLS NEEDED FOR INSTALLATION

- 10mm & 8mm Socket 

- Ratchet & Extension

- T-30 & T-40 Torx Driver

- #3 Phillips Screwdriver

- #2 Phillips Screwdriver

- Panel removal tool

L

R

PARTS LIST 2/4

Summary of Contents for RZ34-Q5XARC




















Reviews: