SST Automation GS11-EI User Manual Download Page 31 | Manualshive

Page: 31 / 51

background image

User Manual

Embedded EtherNet/IP Module

GS11-EI

30

7. Configuration Software (EemTest)

7.1 Overview

EemTest is software based on Windows platforms, used to test embedded Ethernet module GS11-MT and

GS11-EI. The software function is to test the data transceiver of GS11-EI and GS11-MT. The manual introduces

the method of testing GS11-EI. You can obtain the method of testing GS11-MT in GS11-MT user manual.

You need to use the software with GS11-EI development board. We are very sorry that the testing software

may have bugs!

Double click the icon to enter the main Window:

7.2 User Interface

The main interface includes: Parameters Configuration section, Data Receiving section, Data Transmitting

section and some functional button.

Note:

In the software, all the gray parts cannot be changed.

«
...
29
30
31
32
33
...
»

Summary of Contents for GS11-EI




















































Reviews:

No comments

Related manuals for GS11-EI

Relion 670 series

Brand: ABB Pages: 760

Brand: ABB Pages: 128

Brand: Panasonic Pages: 16

Brand: Calsense Pages: 74

Brand: Danfoss Pages: 7

Brand: Lawler Pages: 4

Brand: Hama Pages: 46

Brand: Galcon Pages: 35

Brand: Farfisa Pages: 20

Brand: Racal Instruments Pages: 64

Brand: FATEK Pages: 10

Brand: GCE Pages: 24

Brand: hager Pages: 62

coviva Smartbox TKP100A

Brand: hager Pages: 45

Brand: Uclear Pages: 40

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands