background image

©2022, Sprint Electric. All rights reserved.

We accept no liability whatsoever for the installation, 

fi tness for purpose or application of this product. 
It is the user’s responsibility to ensure the unit is 

correctly used and installed.
This leafl et is protected by copyright. No part of it may 

be stored or reproduced in any form without written 

permission from Sprint Electric. 
The information in this publication was correct at the 

time of going to print. 
We reserve the right to modify or improve the product 

without notifi cation.

The contents of this manual shall not become part of 

or modify any prior existing agreement, commitment, 

or relationship. The sales contract contains the entire 

obligation of Sprint Electric. The warranty contained in 

the contract between the parties is the sole warranty of 

Sprint Electric. Any statements contained herein do not 

create new warranties or modify the existing warranty.
We will be under no liability for any defect arising from 

fair wear and tear, negligence, wilful damage, misuse, 

abnormal working conditions, failure to follow the 

manufacturer’s instructions, unauthorised alteration or 

repair of hardware, unauthorised or accidental alteration 

of software or confi guration, lost profi ts, commercial 

loss, economic loss, or loss arising from personal injury. 

We may, at our discretion, raise a charge for any faults 

repaired that fall outside the warranty cover.

Sprint Electric Limited, Peregrine House, Ford Lane, Ford, Arundel  BN18 0DF, U.K.

Tel: +44 (0)1243 558080  Fax:+44 (0)1243 558099  Email: [email protected]

www.sprint-electric.com

Summary of Contents for JL/X Series





































































Reviews: