Spirax Sarco TVA DN100 Installation And Maintenance Instructions Manual Download Page 41

Page: 41 / 52

IM-P192-02

MI Issue 2

xxxx

SWVER

SEt

PASS

4.10 SWVER

This allows the software version to be viewed.

4.11 SEt PASS

This allows the default pass code to be changed

to a user defined value.

It is important that if the default pass code is

changed that the new value is noted and kept safe.

The new pass code can be recorded on the Table

in Section 9, page 50.

4.9.3 CONSt ALARM

This allows the constant flow alarm to be turned off.

The constant alarm is switched to on by the default factory setting. It detects if the flow has

been constant for long periods when at pressure, which may indicate a stuck cone due to

debris. If the system that the TVA is fitted to, has long periods where there is zero flow, but

the line is kept at a constant pressure, it is advisable to turn the alarm off to avoid unwanted

alarm messages.

This enables the saturated steam alarm.

OFF

This disables the saturated steam alarm.

dELAy

This enables the time duration before alarm is displayed.

4.9.4 SAt ALARM
yES

Enables the Sub Saturation Alarm.

Disables the Sub Saturation Alarm.

dELAy

This sets the time duration before alarm is displayed. Can be zero.

This allows the Sub Saturation Alarm to be enabled or disabled.

The Sub Saturation alarm is switched off by default. If set it will alarm if the steam temperature

drops 2 °C below saturation temperature.

Summary of Contents for TVA DN100





















































Search results

Summary of Contents for TVA DN100

Reviews:

Related manuals for TVA DN100

Brands by name

Popular brands

Spirax Sarco TVA DN100, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for TVA DN100

Reviews:

Related manuals for TVA DN100

Brands by name

Popular brands