Spirax Sarco TVA DN100 Installation And Maintenance Instructions Manual Download Page 37

Page: 37 / 52

IM-P192-02

MI Issue 2

4.6.7 Pulse Output

This sub-menu allows the pulsed output to be configured.

4.6.8 PULSE

This selects whether the pulsed output is to be used or

disabled.

4.6.9 SORCE

This selects the source data for the pulsed output.

The source data can be either unit mass per pulse (tOtAL) or unit energy per pulse (ENRGy).

4.6.10 NUM / PULSE

This allows the total mass, or energy, which is equivalent to one pulse to be configured.

Units are dependent on the UNIt setting. Metric units will be kg for total or MJ for energy,

imperial units will be lb for total or kBtu for energy.

4.6.11 PULSE WIDTH

This allows the width of the pulse to be set. The width can be set in 0.01 second increments

from 0.02 seconds to a maximum of 0.2 seconds.

4.6.12 COMMS

This allows the connection to other communications protocols.

PULSE

NUM/

PULSE

WIDTH

SORCE

yES

xxxmS

xxxxx

tOtAL

ENRGy

COMMS

bAUD

tyPE

ASCII

1200

9600

MOdbuS

Add

xxx

Press OK to select

4.6.13 bAUD

This allows the communication speed to be set to either 1200 or 9600. This must match the

rate set within the device it is communicating to.

4.6.14 tyPE

This gives the choice to select either ASCII or Modbus protocols.

4.6.15 Add

If you have selected Modbus communications you must add an address. This is a three digit

number between 001 - 255. Again this must match the address that the device that you are

communcating to is set to.

Summary of Contents for TVA DN100





















































Search results

Summary of Contents for TVA DN100

Reviews:

Related manuals for TVA DN100

Brands by name

Popular brands

Spirax Sarco TVA DN100, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for TVA DN100

Reviews:

Related manuals for TVA DN100

Brands by name

Popular brands