background image

1

OPERATING INSTRUCTIONS

Thin TRMS, Bluetooth, Autoranging Multimeter

DM6850T

Rotary Switch

OFF

Power off

Capacitance

AC/DC Voltage Measurement

AC/DC Current Measurement

Diode / Continuity / Resistance
Measurement

NCV

Non-contact Voltage Measurement

Hz%

Frequency / Duty Cycle

˚C ˚F

°C/°F Temperature Measurement

A

A

400A

400A

A

A

400A

400A

A

A

400A

400A

Read this owners manual thoroughly before use and save.

IMPORTANT: RECEIVING INSTRUCTIONS

   

Visually inspect all components for shipping damage. If you find damage, notify the carrier at once. 
Shipping damage is NOT covered by warranty. The carrier is responsible for all repair or replacement costs resulting from damage in shipment.

1.0 METER FUNCTIONS & DISPLAY SYMBOLS

1.1 FUNCTIONS (Figure 1)

1. Display: Backlit 3999 Count LCD screen
2.  SELECT Button: Press to switch between:

• DC voltage and AC voltage measurement functions
• Resistance, diode, and continuity test functions
• Frequency and Duty Cycle measurement functions
• DC current and AC current measurement functions
• Celsius temperature and Fahrenheit temperature measurement functions
Hold for about 2 seconds to enable or disable Bluetooth communication
3.  RELATIVE Button: Press to enter or exit Relative mode. Hold for about  

2 seconds to start or stop recording readings in the memory of the meter.

4.  10A Terminal: Red test lead input jack for current measurements.
5.  COM Terminal: Black test lead input jack common to all measurements.
6.  INPUT Terminal: Red test lead input jack for all measurements  

except  current measurements.

7.  Rotary Switch: Turn to power the meter on and off and select the desired 

measurement function. To save battery power, turn to the 

“OFF”

 position when  

the meter is not in use. See 

“ROTARY SWITCH”

 section for function descriptions.

8.  MAX/MIN Button: Press to enter or exit the Min/Max recording mode.
9.  HOLD Button: Press to enter or exit the Data Hold mode.  

Hold for about 2 seconds to turn the backlight on or off. .

1.1  METER FUNCTIONS

Meter type:  

Auto

Display Count:  

3999

Sampling Rate:  

About 2 to 3 times/sec

Battery:  

Requires 2 AAA batteries

Input impedance:  

10 Meg Ohm

AC Volt Ranges:  

4V, 40V, 400V, 600V, best accuracy (1.0%+5)

DC Volt Ranges:  

400mV, 4V, 40V, 400V, 600V, best accuracy (0.5%+5)

AC Amps:  

4A, 10A, best accuracy (1.0%+5)

DC Amps:  

4A, 10A, best accuracy (1.0%+5)

Resistance Ranges:  

 400ohm, 4kohm, 40kohm, 400kohm, 4M ohm,  
and 40M ohm, best accuracy (0.8%+3)

Over Range Indication:  

 Displayed value > 3999 or the input  
measurement range, displays OL 

Frequency Ranges:

  

 9.999Hz, 99.99Hz, 999.9Hz, 9.999kHz, 99.99kHz,  

999.9kHz, 9.999MHz, best accuracy (1.0%+5)

Duty Cycle Range:

  

5%-95%

Capacitance Ranges:

  

 9.999nF, 99.99nF, 999.9nF, 9.999uF, 99.99uF, 999.9uF,  

best accuracy (2.5%+5)

Temperature Ranges:

  

-4°F–1832°F (-20°- 1000°C)

Diode Test:

  

 The approximate forward voltage drop of the  

diode will be displayed  

Continuity Test:

  

 Buzzer will sound if the resistance is < ~30

Ω

Non-contact Volt Ranges:

   50 VAC, 120 VAC, 500 VAC

Polarity Indication:  

“-” is displayed for negative polarity

Overload Protection:  

10A/600V Fast fuse

Agency Approvals:  

ETL, CE (IEC/EN61010:, CAT III 600V, Pollution Degree 2)

Operating Temperature:   32°F–104°F (0°C–40°C)

Relative Humidity:  

< 75%

Storage Temperature:  

14°F–122°F (-10°C–50°C)

IP Degree:  

IP20

Dimension:   

176mm x 81mm x 17mm

Weight: 

Around 180g (without batteries)

Altitude:  

Maximum 2000m

Warranty Info:  

Limited lifetime warranty

Figure 2

1

2

9

7

6

5

4

3

8

Figure 1

Summary of Contents for DM6850T















Reviews: