Spectra Watermakers VENTURA 150 Installation And Operation Manual Download Page 22

Page: 22 / 74

Watermakers should never be run unattended.

Tank Full

If a tank switch has been installed, the

“

Running

”

and

“

Stopped

”

lights will be

illuminated when the tank is full and the
system will stop.

Your watermaker should never be left running unattended.

WARNING

Optional Tank Switch

Cont.

The customer supplied float switch must be connected to the

Terminals 5 & 6

labeled

Tank

Full

within the Control Box that is mounted to the inside of the Feed Pump Module

There is

no polarity. Remove the jumper. Connect the wires to the terminals.

Use 18/2 tinned wire or larger. Wire is not included in the installation kit.

Connect to
Terminals 5 & 6

Note:

Remove

only

the jumper in terminals 5 & 6.

Summary of Contents for VENTURA 150











































































Search results

Summary of Contents for VENTURA 150

Reviews:

Related manuals for VENTURA 150

Brands by name

Popular brands

Spectra Watermakers VENTURA 150, Installation And Operation Manual

Search results

Summary of Contents for VENTURA 150

Reviews:

Related manuals for VENTURA 150

Brands by name

Popular brands