background image

4

WARNING: 

Before Installing this product, read and follow all warning notices and instructions which are included. 

Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call 
(800) 223-8538 or visit www.usa.speck-pumps.com for additional copies of these instructions.

 

Important Safety Instructions

Important Notice:

This manual contains important information about the installation, operation and safe use of this product. This 
information should be given to the owner and/or operator of this equipment. 

WARNING: 

This product must be installed and serviced by a qualified pool professional, and must conform to all 

national, state, and local codes. 

WARNING: 

Before Installing this product, read and follow all warning notices and instructions which are included. 

Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call 
1-800-223-8538 or visit www.usa.speck-pumps.com for additional copies of these instructions.

When installing and using this electrical equipment, basic safety precautions should always be followed, 

including the following:

READ AND FOLLOW ALL INSTRUCTIONS

WARNING:

 To reduce the risk of injury, do not permit children to use this product unless they are closely 

supervised at all times.

WARNING:

 Risk of Electrical Shock. Connect only to a grounding type receptacle protected by a ground-fault 

circuit-interrupter (GFCI). Contact a qualified electrician if you cannot verify that the receptacle is protected by 
a GFCI.

The unit must be connected only to a supply circuit that is protected by a ground-fault circuit-interrupter (GFCI). 
Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push 
the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI 
fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test 
button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this 
pump. Disconnect the pump and have the problem corrected by a qualified service representative before using.

CAUTION:

 This pump is for use with permanently installed pools and may also be used with hot tubs and spas if 

so marked. Do not use with storable pools. A permanently installed pool is constructed in or on the ground or in 
a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it may 
be readily disassembled for storage and reassembled to its original integrity.

TO REDUCE THE RISK OF ELECTRICAL SHOCK, 

connect ground wires to grounding screw located in the motor. 

Use no smaller than a #12 AWG (3.3mm

2

) wire.

TO REDUCE THE RISK OF ELECTRICAL SHOCK, 

a bonding connector is provided for bonding to metal water 

pipes, metal rails, or other metal within 5 feet of the swimming pool. All local points should be bonded with a #8 
AWG (8.4mm

2

) wire.

SAVE THESE INSTRUCTIONS.

Summary of Contents for 1.1 THP Dual Voltage Series





























Reviews: