MODE 3.1 Installation Instructions
Page 17
Line Ou
t
Expansio
n
Aux. Inpu
t
iP
od Base
24V DC
Line Ou
t
Expansio
n
Aux. Inpu
t
iP
od Base
24V DC
Line Ou
t
Expansio
n
Aux. Inpu
t
iP
od Base
24V DC
Line Ou
t
Expansio
n
Aux. Inpu
t
iP
od Base
24V DC
Line Ou
t
Expansio
n
Aux. Inpu
t
iP
od Base
24V DC
Line Ou
t
Expansio
n
Aux. Inpu
t
iP
od Base
24V DC
12V DC 1 AMP
Adaptor Port
Aux. Input
USB
12V DC 1 AMP
Adaptor Port
Aux. Input
USB
12V DC 1 AMP
Adaptor Port
Aux. Input
USB
12V DC 1 AMP
Adaptor Port
Aux. Input
USB
12V DC 1 AMP
Adaptor Port
Aux. Input
USB
12V DC 1 AMP
Adaptor Port
Aux. Input
USB
MODE ADAPTER #1
MODE ADAPTER #2
MODE ADAPTER #3
MODE ADAPTER #4
MODE ADAPTER #5
MODE ADAPTER #6
MODE BASE #1
MODE BASE #2
MODE BASE #3
MODE BASE #4
MODE BASE #5
MODE BASE #6
Adapter
Port
iPod Base
Port
Line Out
Adaptor
Interconnect
CAT5
CAT5
CAT5
CAT5
CAT5
CAT5
CAT5 To MZC Expansion Port
One Connection for all Adapters
Stereo Mini
to RCA
To MZC
Source In
Stereo Mini
to RCA
To MZC
Source In
Stereo Mini
to RCA
To MZC
Source In
Stereo Mini
to RCA
To MZC
Source In
Stereo Mini
to RCA
To MZC
Source In
Stereo Mini
to RCA
To MZC
Source In
SpeakerCraft
PS-3.0 24VDC
Power Supply
One Powers all Adapters
MODE ADAPTER (Stacked)
1. Stack the Adapters and confi rm connection of the 12-pin interconnects as described in section:
Installation
.
2. Using a CAT5 patch cable with a pass-through confi guration, connect the
Expansion Port
on
one
of the
MODE
Adapters
to the
Expansion Port
on a
MZC-66/88
. (The 12-pin interconnects create a bus for power, control and
metadata to the additional units.)
3. Using the included
Stereo mini to RCA interconnect cables
, connect the 3.5mm
Line Out Jack
on
each
Adapter
to the appropriate
Source Input
on the
MZC-66/88
.
4. Using a CAT5 patch cable with a pass-through confi guration, connect the
iPod Base Port
on
each MODE Adapter
to
the
Adapter Port
on
its specifi cally matched
MODE Base
. Repeat until all Adapters and Bases are connected. If CAT5
cable was pulled during pre-wire and terminated with a wall plate in the remote zone, connect the cable to the iPod
Base Port on the MODE Adapter. Connect the RJ45 jack on the wall plate to the Adapter Port on the MODE Base using a
CAT5 patch cable with a pass-through confi guration.
5.
Aux Input (optional) -
Using a
Stereo mini to RCA interconnect cable
, connect the
L&R line level audio output
of a
source
to be added as an additional input such as an XM or Sirius Tuner, Cable or Satellite receiver, etc. to the
Aux
Input
on the appropriate Adapter as confi gured in
Source Setup
in
EZ-Tools
. This will allow adding up to six additional
sources to the MZC. These inputs must be confi gured in EZ-Tools and are only selectable from MODE Keypads.
6. When all connections have been made and confi rmed and the system is ready for operation, connect a SpeakerCraft
PS-
3.0 Power Supply
to the
24V DC Jack
on
one
MODE Adapter
. This will provide power for up to six MODE Adapters.
Plug the PS-3.0 into an unswitched 120VAC outlet.
Figure 12
Multiple MODE Adapter/Base Connections