manualshive.com logo in svg

Space Pak SIS Series, Manual, Page: 35 / 44

Share
Download
Space Pak SIS Series Manual Download Page 35

– 35 –

Split Inverter Air-to-Water Heat Pump

Parameter List

Operation

Section Code Description

Units

Range

Default Notes

H

H01 EVI Operation

N/A

0 to 3

3

0 = EVI Inactive, 1 = EVI in Cooling, 2 = EVI in Heating, 3 = Both

H02 Running Mode

N/A

0/1

0

Manufacturer setting, do not alter

H03 Auxiliary Electic Heater

N/A

0/1

0

0 = No Aux Heater, 1 = Aux heater installed and active

H04 Heat Pump Mode

N/A

0 to 2

0

Manufacturer setting, do not alter

H05 Remote Enable & Heat Cool selection

N/A

0/1

0

0 = Console touchscreen operation, 1 = Wired remote operation

H06 Not Used
H07 Not Used
H08 Not Used
H09 Not Used
H10 Temperature Measurement Units

N/A

0/1

1

0 = Celsius, 1 = Farenheit

H11

DHW Operation

N/A

0/1

0

0 = DHW operation disabled, 1 = DHW operation enabled

H12 Not Used
H13 Not Used

P

P01

Pump Operation

N/A

0 to 2

0

0 = For Console Operation, 1 = For Wired Operation, 2 = Interval

P02

Interval Pump Off duration

Min.

1 to 120

10

If P01 = 2, Pump Starts every P02 minutes when no call is present

P03

Interval Pump On duration

Min.

1 to 30

3

If P01 = 2, Pump runs for P03 minutes, or until call is satisfied

P04

Not used

 

 

R

R01 Supply Temp target setpoint, Cooling

Deg F

R16 to 77

42

Cannot be less than the value of R16

R02 Supply Temp target setpoint, Heating

Deg F

77 to R15

120

Cannot be greater than the value of R15

R03 Difference from setpoint to Start Cooling

Deg F

0 to 18

6

Compressor starts in cooling when water temp rises to R01 + R03

R04 Difference from setpoint to End Cooling

Deg F

0 to 18

2

Compressor stops in cooling when water temp falls to R01 - R04

R05 Difference from setpoint to Start Heatling

Deg F

0 to 18

10

Compressor starts in Heat when water temp falls to R02 - R05

R06 Difference from setpoint to End Cooling

Deg F

0 to 18

4

Compressor starts in Heat when water temp rises to R02 + R06

R07 Difference fromsetpoint for Electric Heat

Deg F

0 to 18

4

Electric heaters enabled when water temp is below R02 - R07

R08 Ambient temp for Electric heat w/Delay

Deg F

-58 to 68

20

Electric heaters available after delay when ambient is below R8

R09 Time Delay duration

Min.

0 to 120

10

Time delay in minutes for activiation of Electric Heaters

R10 Ambient Temp for Electric heat w/o Delay

Deg F

-58 to 68

-5

Electric heaters available immediately when ambient is below R10

R11

DHW Temp Setpoint

Deg F

95 to 131

125

Target setpoint of DHW Tank when enabled

R12 DHW differential to Start

Deg F

0 to 18

10

DHW Starts when Tank temp falls to R11 - R12

R13 DHW differential to End

Deg F

0 to 18

4

DHW Stops when Tank temp rises to R11 + R13

R14 Not used

 

 

 

 

R15 Maximum Heating Setpoint

Deg F

113 to 158

140

R02 Cannot be set greater than this value

R16 Minimum Cooling Setpoint

Deg F

35.6 to 53.6

36

R01 Cannot be set lower than this value

U

U01 Not used

 

U02 Not used

 

U03 Not used

 

Summary of Contents for SIS Series













































Reviews:

No comments