Sourcetronic ST9201 Series User Manual Download | Manualshive

Page: 49 / 94

background image

◇

49

Chapter 5 ST9201 RS232

Commands

5.1 Commands for System settings

:SYSTem:VERSion?
                          Inquires about the version of the tester.
                              --Syntax:
                                          Command message:
                                          Query message:
                                                                  :SYST:VERS?

                              --Example:
                                          :SYST:VERS?
                              --Response message
                                          If the version of the tester is 1.00,
                                          Ver 1.00 is returned.

:SYSTem:TIME:PASS
Sets the pass hold time in a PASS judgment.

Also inquires about the current PASS hold time.

                              --Syntax:
                                          Command message:      :SYST:TIME:PASS <time>

                                          Query message:
                                                                  :SYST:TIME:PASS?

                              --Program data:
                                          Data format:float
                                          Set value: 0.3~99.9
                                          Resolution: 0.1
                                          Unit: s

                              --Example:
                                          To set the PASS hold time to 1.0s,
                                          :SYST:TIME:PASS 1.0
                              --Example:

:SYST:TIME:PASS?
If the current PASS hold time is 1.0,
1.0 is returned.

«
...
47
48
49
50
51
...
»

Summary of Contents for ST9201 Series































































































Reviews:

No comments

Related manuals for ST9201 Series

Brand: MacDon Pages: 17

Brand: Olympus Pages: 50

Brand: VAHVA Pages: 19

Brand: idiag Pages: 12

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: Eaton Pages: 16

Brand: Eaton Pages: 6

Brand: Ecco Pages: 17

Brand: Fayat Group Pages: 50

Brand: Halyard Pages: 88

Brand: Garelick Pages: 2

Brand: Garelick Pages: 2

Brand: Gardigo Pages: 32

Brand: Patiova Pages: 19

Brand: Garmin Pages: 12

Brand: Garmin Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands